Snow Performance Water-Methanol

Stage 1 Diesel Boost Cooler™

This kit progressively injects more or less water-methanol, according to manifold boost pressure.
The system is applicable for turbo diesels making up to 25psi of boost pressure. It has two dials to
set the start and full points to tailor the delivery to your engines needs. Progressively injecting
according to boost pressure allows for the most power over the widest range of rpms.
Now with Lifetime Warranty - please see details.

48001 Diesel Stage 1 Boost Cooler™ 93-96 GM 6.5 - $504.00
50001 Diesel Stage 1 Boost Cooler™ 93-98 Ford 7.3 Powerstroke - $504.00
47001 Diesel Stage 1 Boost Cooler™ Universal ( less than 25 psig boost) - $504.00

Stage 2 Diesel Boost Cooler™

These kits work on exactly the same principle as the Stage 1 kits, except that the controllers are
heavier duty and can read up to 100psi of turbo boost. This is the typical starting point for a
mildly modified modern 3/4 or 1 ton truck with an aftermarket exhaust, intake and chip or
programmer. It is capable enough for trucks running large or compound turbo systems
as well. These kits allow for great horsepower increases and EGT reductions – expect about 70hp
and 250 degree F EGT drop. Now with Lifetime Warranty - please see details.

49002 Stage 2 Diesel Boost Cooler™ Dodge Cummins - $611.00
48002 Stage 2 Diesel Boost Cooler™ GM Duramax - $611.00
50002 Stage 2 Diesel Boost Cooler™ Ford 7.3 Powerstroke - $611.00
50012 Stage 2 Diesel Boost Cooler™ Ford 6.0 Powerstroke - $611.00
48004 Stage 2 Diesel Boost Cooler™ HOBBS - $469.00
47002 Stage 2 Diesel Boost Cooler™ Universal - $541.00

Stage 3 Diesel Boost Cooler™

The Stage 3 Diesel Boost Coolers™ are the most comprehensive water-methanol injection kits
Snow Performance makes. This controller senses not only manifold boost pressure but also
exhaust gas temperatures. Using two inputs allows for the smoothest injection control. More
importantly, it also keeps the EGTs as low as possible – if they begin to climb, even if the boost
stays constant, the Stage 3 controller will read this and inject more water-methanol to compensate.
Additionally, the controller has readouts for EGT, Boost and Water-Methanol Injection so at
a glance you can see what is going on with your engine and not need to mount any additional
gauges. Finally, there is an adjustment knob on the controller to allow tuning changes from the
driver’s seat on-the-fly. There is even a switch on the controller to allow it to operate off of just
boost pressure (ignoring the EGT input). This can be advantageous if you want the quickest
response if you are at the drag strip or if a sports car pulls up next to you at a stop light. There are
2 levels of Stage 3 Boost Cooler™ available, one for lower boost (up to 25psi) and one for higher
boost (up to 100psi). Now with Lifetime Warranty - please see details.

49003 Stage 3 Diesel Boost Cooler™ Dodge Cummins - $824.00
48003 Stage 3 Diesel Boost Cooler™ GM Duramax - $824.00
50003 Stage 3 Diesel Boost Cooler™ Ford 7.3 Powerstroke - $824.00
50013 Stage 3 Diesel Boost Cooler™ Ford 6.0 Powerstroke - $824.00
47003L Stage 3 Diesel Boost Cooler™ Universal Low Boost - $824.00
47003 Stage 3 Diesel Boost Cooler™ Universal - $824.00

Bulkhead Fitting

This is a metal bulkhead fitting that allows a safe pass through on a firewall or in a reservoir (like a
factory washer fluid tank) with quick connects on both sides. Threaded body can be tightened down
with nuts on both sides, or in plastic tanks can be threaded in with methanol resistant (GOOP brand
recommended) sealant for a leak-free installation.

40080 Bulkhead Fitting - $15.00

Low Level Indicator

This is a float switch and indicator light that lets you know when your reservoir is running
low on fluid. Simple to install and wire in any reservoir.

40030 Level Switch Upgrade - $49.00
40035 Level Switch (Unmounted) - $39.00

7 Quart Reservoir

The 7 quart reservoir gives much more range than the included 2 qt tanks, and is fairly small in size
– 10”l x 12”h x 7”w (similar to a very small car battery) and includes an additional 10 feet of hose.

*NOTE* It is recommended that a Solenoid Upgrade (part #40060) be used in any
application that utilizes a trunk mounted reservoir.

40020 7 Quart Reservoir - $59.00

Boost Juice™

Boost Juice™ is Snow Performance’s proprietary mix of 49% methanol and 51% water.
It is made in a controlled environment with special care to make sure the ratios are accurate to
result in a high performance water-methanol fluid formulated for use in the Boost Cooler™
injection system. If Boost Juice™ is used exclusively in the Boost Cooler™ kit,
Snow Performance offers a free lifetime warranty.

40008 Boost Juice™ 4 gal case - $30.00

8 Gallon Reservoir

The 8 gallon reservoir is used mainly for diesel trucks and gives a range of 5-600 miles when towing
around 12,000 lbs. It comes with a mounting bracket, an extra 10 ft of hose and a shut-off solenoid
to prevent gravity feeding if you ever park on a steep incline. Measurements: 16”l x 17”h x 13”w.
This size allows it to mount inside of most bed-mount tool boxes.

40010 8 Gallon Reservoir - $184.00

Reverse Flow Check Valve

This valve, mounted between the reservoir and the pump inlet, is used to keep boost from
reverting back through the reservoir during the pre-injection state.
Recommended in high boost (over 60 psig) applications.

*NOTE* Check valve is not required when using pumps that were purchased after September 2005.
All new pumps now include an internal check valve rated to 60 psi.

40005 Reverse Flow Check Valve - $29.95

150 PSI Pump

Our new higher volume/pressure pump is now the standard pump that is included in all of our kits.
The 150 psi pump can support 1000-1500 hp. Pressure adjustable from 150-180+ psi.

40150 150 PSI Pump - $116.00

220 PSI Pump

The 220 psi pump is high pressure/volume pump that’s only necessary in the highest horsepower
applications. It is for use with systems running three or more large nozzles or if more injection
quantity is needed. Adjustable pressure just like our 150 psi pumps. Suggested for diesel
applications running more than 50 psi of boost.

*NOTE* It is suggested that the VC100 controller be used in conjunction with the 220 psi pump.

40220 220 PSI Pump - $145.00
40220U 220 PSI Pump Upgrade (when purchasing kit) - $39.95

Nozzle Mounting Bung

NOW AVAILABLE! Weldable threaded bungs make installing your injector nozzle easier
when using thin-walled intake tubing. Simply drill a hole in your intake tube and weld
in the bung. Your nozzle then has a strong threaded connection that can be used
with confidence. Available in steel or aluminum.

1" diameter, 1/4" thick, 1/8" NPT threads for Snow Performance Boost Cooler nozzle.
Can also be used with nitrous nozzles, boost port fittings, etc.

40120 Nozzle Mounting Bung - Aluminum - $20.00
40130 Nozzle Mounting Bung - Steel - $20.00

Nozzle Mounting Adapter

NOW AVAILABLE! Need a way to mount your injector nozzle into your silicone or
rubber intake tube? Snow Performance now offers a Nozzle Mounting Adapter for
those without metal intake tubes.

Made from Delrin, the adapter is methanol resistant and highly durable.
Installation is easy: simply drill a 3/4" hole using a spade bit, insert the inner adapter piece,
and thread on the outer adapter nut.

40110 Nozzle Mounting Adapter - $20.00

Water Injection Kits Systems

Kit includes:
• 150+ PSI High Volume Pump
• 2 Quart Reservoir
• Bulkhead Fitting
• Digital Variable Controller
• 2 Nozzles To Cover a Wide Range of Horsepower
• All Required Hardware Needed For Installation
• Comprehensive Instructions

Kit includes:
• 150+ PSI High Volume Pump
• 2 Quart Reservoir
• Bulkhead Fitting
• Digital Variable Controller
• 3 Nozzles To Cover a Wide Range of Horsepower
• All Required Hardware Needed For Installation
• Comprehensive Instructions

Toll Free: 877-DPP-POWER Local: 417-859-0895
Fax: 417-859-0896 Email to: sales@dpppower.com